Crew services · mount, bracket, anchor

A fixture install crew with one narrow Craft

NBD Installs LLC exists to install fixtures on walls, ceilings and rack frames, then prove the anchors hold. The crew works from the yard at 2788 W 7180 S, West Jordan - 84084-2931, United States (US) and runs six connected service lines. Read them here in the order a job moves through them. Ask the crew about a survey → Each line below is a full run, not a snapshot, so you can see where the handoff happens.

Request the service sheet

Six services, one sequence

From the first survey mark to the last signature

Every service below is delivered by the same two-person crew that signs the certification sheet. We do not subcontract the anchor work, and we do not leave a bracket for another trade to finish.

Mount Rig Setup

Mount rig setup is the part of the job the client sees least and feels the most. On the first morning the crew lays out boom arm sections, standoffs and rail stock on a clean sheet, checks every joint by hand and confirms the torque values against the manufacturer sheet. We build the rig flat, then walk it upright as a pair so nothing twists on the lift. If the room has a low ceiling or a tight return wall, the boom arm is shortened at the bench rather than forced into place in the air. The rig is not left unbraced at any point. When it goes up, the crew reads the level bubble against the rail and adjusts the standoffs before the first anchor is set.

Bracket Package Fits

A bracket package is only as good as its fit to the device, the substrate and the service loop behind it. We open every package against the device profile before we mark the wall, dry-fit the assembly and check the clearances for cable and air. If a package does not land cleanly on the framing, we do not shim it into a lie. The crew returns it to the bench, re-drills the plate pattern or swaps to a bracket family that matches the stud spacing. That dry fit is the reason bracket installation rarely needs a second visit.

Anchor Certification Days

Certification days are scheduled as a separate slot because they cannot be rushed. The crew works the anchor schedule bay by bay, records the substrate type, the drill depth, the anchor family and the torque value for each stud, then tags anything that does not pass. A wall that was hidden by a finished surface is not guessed at: we probe, we mark, we record. The certification sheet leaves the site with the client, not in a truck. If a later trade needs to open the wall, the sheet tells them exactly what is behind it.

Load Test Rounds

Load test rounds pull a sample of anchors at a set percentage above the rated working load and log the deflection as each one takes tension. The crew runs tests in rounds so a failure stops the schedule before the next bay is touched. A failed pull on test day is a repair; a failed pull on install day is a claim. We would much rather find the loose one with the tester in hand. Deflection readings go onto the same sheet as the certification record so the two can be read side by side.

Wall Prep Sessions

Wall prep is where a clean install is won. The crew maps the framing with a stud finder and a tap line, marks each bay, cuts access openings where the service loop needs to pass and confirms the substrate against what the drawings claim. Drywall, block, steel stud and timber each get a different prep note, and the crew writes that note on the wall in pencil so the next visit does not start from zero. At the end of a prep session the bays are marked and the anchor schedule is ready for certification day.

Punch List Walks

The punch list walk is the crew walking the room with the client, bay by bay, reading the certification sheet out loud and confirming every anchor against the plan. We fix anything that has drifted on the spot where the fix is small, and we write down the fix where it is not. The walk ends with a signed record and a clean handoff, and the crew does not close the job until the last line on the list is checked.

Every service run returns to the same rail, which is why the certification sheet from the first bay can be read against the punch list from the last one.

How the runs connect

The six services are not a menu the client picks from. They are a sequence with clear handoffs. Mount rig setup and bracket package fits run in parallel on the same day when the room allows it, wall prep runs ahead of certification, load test rounds bracket the certification day and the punch list walk closes the room. If a client only needs one run, for example an anchor certification day on an existing rig, we will do that run on its own and hand over the record.

What we will not do is certify an anchor we did not set without a tester in hand, and we will not sign a punch list for a rig we did not assemble. The record has to mean something, and it only means something if the crew that signs it also did the work.

What a service visit includes

A walk of the room with the client before the first mark
A printed anchor schedule keyed to bay and stud
Torque and pull values recorded on the same sheet
A signed handoff at the end of the punch list walk

Ready to schedule a run

Send the room plan and the device schedule to the crew and we will return a survey date. The phone line is +16827668642 and the inbox is relay@nbdinstalls.buzz.

Open the contact form